1. Solution home
  2. How-To's
  3. Entagged
Open navigation

Plug the Entagged device into your camera

Table of contents


Overview

This article covers the setup and installation process for the different Entagged models (M, N1, N2), focusing on connecting the magnetic USB plug, positioning HDMI/USB cables, and ensuring proper functionality through compatibility checks. Unique installation details for each model are included.


Setting Up Your Entagged Device

Before you begin, ensure you have the correct Entagged model, USB or HDMI cable, and magnetic plug (if applicable) for your camera. You can check the Entagged compatibility list.

Disable the following settings before plugging in your Entagged device (if available on your camera):

  • USB charging
  • Built-in WiFi
  • FTP Upload
  • LAN
  • Tethering

Please note: In this article, "USB" refers to USB-C, Micro-USB, Mini-USB, and USB-8P ports and cables. Similarly, "HDMI" will refer to standard HDMI (HDMI-A), Mini-HDMI (HDMI-C), and Micro-HDMI (HDMI-D) ports and cables. The type of cables needed depends on your camera model, which is why providing this information is necessary when purchasing your Entagged device. The setup process and outcome are the same.


Canon Setup

  1. .Snap the magnetic USB plug onto the back of the Entagged device.
  2. With the Entagged logo facing you, ensure its port is facing upwards.
  3. Plug the "Foolography" end of the HDMI cable into the top of the Entagged. The cable should point to the right.
  4. Plug your Entagged device (with attached HDMI cable) into your camera’s USB port, and plug the other end of the HDMI cable into your camera’s HDMI port. If the HDMI cable is too close to the Entagged device, you can rotate the Entagged device by 90º or 180º to allow for more space. You can also tuck the HDMI cable behind the Entagged device for a cleaner look.
  5. Turn on your camera. The LED of the Entagged should now light up. If not, check that the cable is plugged in the correct direction (step 3) as this is one of the most frequent missteps.
An image showing the Entagged device connected to a Canon camera via the USB port, and a second HDMI cable also connected from the device to the camera.

If your camera has a Micro-USB 3.0 port: The Micro-USB 2.0 magnetic plug is backward compatible and fits into the wider half of the Micro-USB 3.0 port.


Nikon Setup

The instructions for plugging your Entagged device into your Nikon camera depend on the model of your Entagged device.

N1 Model

  1. For Z8 and Z9 models, change the USB setting in your camera menu to enable camera control:
    1. MENU > NETWORK (Globe)
    2. USB = MTP/PTP
    3. Below, tap Done.
    4. [Advanced] It's also advisable to change these settings:
      MENU -> SETUP (Wrench)
      USB Connection priority = Shooting (Camera)
      USB power delivery = OFF
  2. With the Entagged logo facing you, ensure the Entagged device port is facing upwards.
  3. Plug the "Foolography" end of the USB cable into the top of the Entagged. The cable should point to the right.
  4. Plug the Entagged device into the round 10-pin remote port on the front of your camera. It may be a little challenging to plug in at first, as the Entagged device is designed to fit snugly onto your camera without moving. Wiggling the Entagged a little as you insert it can make this easier.
  5. Plug the other end of the cable into the USB port of your camera.
  6. Turn on your camera. The LED of the Entagged should now light up. If not, check that the cable is plugged in the correct direction (step 3) as this is one of the most frequent missteps.

If your camera has a Micro-USB 3.0 port: The Micro-USB 2.0 magnetic plug is backward compatible and fits into the wider half of the Micro-USB 3.0 port.

An image showing the Entagged N1 device connected to the front of a Nikon Z9 camera, with the cable routed to the side USB port.

N2 Model

  1. For Z6 III, change the USB setting in your camera menu to enable camera control:
    1. MENU > NETWORK (Globe)
    2. USB = MTP/PTP
    3. Below, tap Done.
    4. [Advanced] It's also advisable to change these settings:
      MENU -> SETUP (Wrench)
      USB Connection priority = Shooting (Camera)
      USB power delivery = OFF
  2. With the Entagged logo facing you, ensure the Entagged device port is facing upwards.
  3. Plug the "Foolography" end of the USB cable into top of the Entagged. The cable should point to the left.
  4. Plug the Entagged device into the rectangular remote port on the side of your camera.
  5. Plug the other end of the cable into the USB port of your camera.
  6. Turn on your camera. The LED of the Entagged should now light up. If not, check that the cable is plugged in the correct direction (step 3) as this is one of the most frequent missteps.

If your camera has a Micro-USB 3.0 port: The Micro-USB 2.0 magnetic plug is backward compatible and fits into the wider half of the Micro-USB 3.0 port.

An image showing the Entagged N2 device connected to the side of a Nikon Z6 III camera, with the cable routed to the USB port.

M Model

  1. Snap the magnetic USB plug onto the back of the Entagged device.
  2. With the Entagged logo facing you, ensure its HDMI port is facing upwards.
  3. Plug the "Foolography" end of the HDMI cable into the Entagged HDMI port. The cable should point to the right.
  4. Plug your Entagged device (with attached HDMI cable) into your camera’s USB port, and plug the other end of the HDMI cable into your camera’s HDMI port. If the HDMI cable is too close to the Entagged device, you can rotate the Entagged device by 90º or 180º to allow for more space. You can also tuck the HDMI cable behind the Entagged device for a cleaner look.
  5. Turn on your camera. The LED of the Entagged should now light up. If not, check that the cable is plugged in the correct direction (step 3) as this is one of the most frequent missteps.
An image showing the Entagged M device attached to a Nikon camera via the magnetic USB plug, with the HDMI cable also connected.
Camera Photo by Richard Butler

Sony Setup

  1. Before plugging anything in: In your camera settings, turn on the PC Remote function (Menu → Setup → USB → USB Connection Mode → PC Remote).
  2. If you have previously connected to the Image Edge mobile app via WiFi, please disconnect it.
  3. If you have previously set your camera to transfer FTP over USB, please turn this off (Menu → Network → Transfer/Remote → FTP Transfer Func. → FTP Function → Off).
  4. Snap the magnetic USB plug onto the back of the Entagged device.
  5. With the Entagged logo facing you, ensure its port is facing upwards.
  6. Plug the "Foolography" end of the HDMI cable into the top of the Entagged. The cable should point to the right.
  7. Plug your Entagged device (with attached HDMI cable) into your camera’s USB port, and plug the other end of the HDMI cable into your camera’s HDMI port. If the HDMI cable is too close to the Entagged device, you can rotate the Entagged device by 90º or 180º to allow for more space. You can also tuck the HDMI cable behind the Entagged device for a cleaner look.
  8. Turn on your camera. The LED of the Entagged should now light up. If not, check that the cable is plugged in the correct direction (step 6) as this is one of the most frequent missteps.
An image showing the Entagged device connected to a Sony camera via the USB port and HDMI port.

If your camera has a Micro-USB 3.0 port: The Micro-USB 2.0 magnetic plug is backward compatible and fits into the wider half of the Micro-USB 3.0 port.


Fujifilm Setup

  1. Before plugging anything in: In your camera settings, adjust your USB settings: Menu → Set Up → Connection Setting → (PC) Connection Mode → USB Tether Shooting Auto.
  2. If you have previously connected to the Fujifilm Cam Remote app via WiFi, please disconnect this.
  3. Snap the magnetic USB plug onto the back of the Entagged device.
  4. With the Entagged logo facing you, ensure its port is facing upwards.
  5. Plug the "Foolography" end of the HDMI cable into the top of the Entagged. The cable should point to the right.
  6. Plug your Entagged device (with attached HDMI cable) into your camera’s USB port, and plug the other end of the HDMI cable into your camera’s HDMI port. If the HDMI cable is too close to the Entagged device, you can rotate the Entagged device by 90º or 180º to allow for more space. You can also tuck the HDMI cable behind the Entagged device for a cleaner look.
  7. Turn on your camera. The LED of the Entagged should now light up. If not, check that the cable is plugged in the correct direction (step 5) as this is one of the most frequent missteps.
An image showing the Entagged device connected to a Fujifilm camera via the USB port and HDMI port.

If your camera has a Micro-USB 3.0 port: The Micro-USB 2.0 magnetic plug is backward compatible and fits into the wider half of the Micro-USB 3.0 port.

After correctly plugging your Entagged device into your camera, it's now time to pair your device with your phone or tablet.


The Takeaway

By following these steps, you've successfully plugged in your Entagged device, ensuring a secure and functional connection to your camera. You're now ready to pair your Entagged device with your Entagged app and/or a barcode scanner to enhance your photography workflow.

Was this article helpful?

That’s Great!

Thank you for your feedback

Sorry! We couldn't be helpful

Thank you for your feedback

Let us know how can we improve this article!

Select at least one of the reasons
CAPTCHA verification is required.

Feedback sent

We appreciate your effort and will try to fix the article